Versionen im Vergleich

Schlüssel

  • Diese Zeile wurde hinzugefügt.
  • Diese Zeile wurde entfernt.
  • Formatierung wurde geändert.
Seiteneigenschaften


Description:
This document describes the options for error analysis of WWAN connections (UMTS/3G and LTE/4G) which can be performed on local and remote devices.
Info

Performing remote troubleshooting of a WWAN connection absolutely requires a functional separate Internet connection (e.g. an xDSL connection), which can be used to connect to the device.



Procedures:
The troubleshooting options described in the following are performed in the console of the LANCOM router. You can additionally check many of these parameters with LANmonitor or WEBconfig.
The path /Status/Modem-Mobile shows you all of the information about the WWAN connection and the integrated WWAN modem.
Image Removed
Image Added

1) Check that a SIM card has been properly inserted into the device:
With the command ls /Status/Modem-Mobile/SIM-inserted you can check if a SIM card is present in the device.
  • Yes: SIM card is inserted
  • No: SIM card is not inserted
The path /Status/Modem-Mobile/SIM-inserted is present on all current devices, but may be missing on older devices/firmwares. It indicates physical prensence of a SIM, even if the SIM is unreadable (due to ESD, corrosion, insufficient contact on e.g. Nano-SIMs).
Image Removed
Image Added

2) Check that the PIN has been entered correctly:
Enter the command ls /Status/Modem-Mobile/PIN-Status.
Image Removed
Image Added

3) Check the current WWAN signal strength:
With the command ls /Status/Modem-Mobile/Signal you can check the current signal strength (in dBm).
Information about signal strength and quality is available on the following web page:
Image Removed
Image Added

4) Perform network scan by quality (in LCOS 8.84 RU8 and LCOS 9.10 RU1):
The mobile interface uses a scan initiated manually in LANmonitor or from the command line to search for all available cellular networks and logs into the mobile network with the best signal quality. If this login process fails, the mobile interface uses the semi-automatic network selection.
Console commands:
  • do /Status/Modem-Mobile/Scan-Networks -s -f
    This command initially disconnects any existing 3G/4G WAN connection, it then performs an extended scan and the best network is selected and stored to the configuration. This command is useful in combination with "Semi automatic" and "manual" network selection. The stored network also applies after a device restart (Cold/Warm boot) until Scan-Networks -s/-e is executed, for all modes but automatic. Results of the scan are available at /Status/Modem-Mobile/Network-List.
  • do /Status/Modem-Mobile/Scan-Networks -e -f
    This command initially disconnects any existing 3G/4G WAN connection and it then performs an extended scan. The -e parameter ensures that the best network is found, but this is not entered in the configuration. However, the entry is made in the status tree.
  • do /Status/Modem-Mobile/Scan-Networks -s
    This command is used to perform a network scan only with an inactive WWAN connection.

5) Check the connection history of WWAN connections:
With the command ls /Status/Modem-Mobile/History you can display a tabular overview of all established WWAN connections.
Image Removed
Image Added

6) Check the current routing table:
Use the command ls /Status/IP-Router/Act.-IP-Routing-Tab to check whether a default route for the WWAN connection exists in the routing table.
Image Removed
Image Added

7) Perform a firmware update on the WWAN module:
Updated firmware is available for the WWAN module, offering improvements to the cellular modem integrated into the LANCOM 178x-4G series of routers and the 3G routers.


8) Capture traces for analysis:

8.1) Connect to the router via the LANtrace and import the appended trace configuration into the trace module.
View file
nameUMTS_LTE.lcg
height150

The procedure to create a trace with a prefabricated trace configuration is described in  this Knowledge Base article.

2) Start the trace with a click on the  button with the green arrow  and record the error state.

Hinweis

The dial-in attempt or the termination of the connection has to be included in the trace output!

3) Stop the trace with a click on the   button with the stop sign   and save it with a click on the   button with the floppy disk symbol .


9) Sending the information to LANCOM Support:

If the problem should still persist after conducting the steps in this guide, please contact  LANCOM Support  and attach the following information:

  • Time of the dial-in attempt or connection termination
  • Trace in the error state created with the attached trace configuration (*.lct  file) 
  • Up to date configuration file of the router (*.spf  file)