...
This article describes the meaning of LED blinking characteristics of LANCOM routers and access points.
Info |
---|
If all LEDs glow red permanently, there are two possible causes: - The LEDs were set to red via the LED test
Leuchten alle LEDs dauerhaft rot, gibt es zwei mögliche Ursachen: - Die LEDs wurden über den LED-Test (Setup/Config/LED-Test) rot geschaltet. Über den LED-Test können die LEDs rot, grün und orange geschaltet sowie deaktiviert werden. In diesem Fall funktioniert das Gerät ganz normal. Der Reset-Button klemmt. In diesem Fall befindet sich das Gerät in einer Reset-Schleife und ist daher nicht funktionsfähig. The LEDs can be set to red, green and orange and can also be deactivated via the LED test. In this case the device works normally.
- The reset button is jammed. In this case the device is in a reset loop and doesn't function normally.
|
1) LANCOM router:
Info |
---|
Auf Routern im CPE-Gehäuse (alle Router außer Routers in CPE case (all routers except IAP-4G+, IAP-1781VAW, 190x Serie und and Central Site Gateways) gibt es auf der Oberseite zwei weitere LEDs:feature two additional LEDs on the top side: - Left Linke LED: Power
- Rechte Right LED: Online
|
1.1) VPN router:
ModelBlink-Verhalten aus der Hardware-Schnellübersicht - auf die Bilder klicken zum Vergrößern | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
1640E | | Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
1780EW-4G+ | | WLAN LED blinking red: Hardware error in the Wi-Fi module |
1781EW+ | | WLAN LED blinking red: Hardware error in the Wi-Fi module
LED -Blink-Verhalten der Power-blinking characteristics of the power LED: - 1 x invers grün blinkend: Die LMC ist erreichbar, es besteht aber ein Problem in der LMC (theoretisches Problem, das niemals auftreten sollte)
- 2 x invers grün blinkend: Pairing-Fehler bzw. LMC-Aktivierungscode nicht vorhanden
- 3 x invers grün blinkend: LMC nicht erreichbar bzw. Kommunikationsfehler
- green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error
Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
1781VA | Image Added | Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
1781VA | Image Removed | 1790-4G | | Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
1790EF | | Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
1790VA | | Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
1790VA-4G | | Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
1790VAW | | WLAN LED blinking red: Hardware error in the Wi-Fi module Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
1900EF | |
|
1906VA | |
|
1906VA-4G | |
|
1926VAG | Image Added |
|
1926VAG-4G | Image Added |
|
IAP-4G+ | |
|
1.2 VoIP-Router:
ModelBlink-Verhalten aus der Hardware-Schnellübersicht - auf die Bilder klicken zum Vergrößern | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
883 VoIP / 883+ VoIP / 1793VAW | Image RemovedImage Added | WLAN LED blinking red: Hardware error in the Wi-Fi module Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
884 VoIP / 1784VA | Image Removed | Image Added | Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
1793VA | Image Added | Online LED blinking green: WAN connection setup (e.g. PPP authentication) | 1793VA | Image Removed |
1793VA-4G | | Online LED blinking green: WAN connection setup (e.g. PPP authentication) |
| Image RemovedImage Added | WLAN LED blinking red: Hardware error in the Wi-Fi module |
...
1.3 Central Site Gateways:
ModelBlink-Verhalten aus der Hardware-Schnellübersicht - auf die Bilder klicken zum Vergrößern | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
ISG-1000 | |
|
ISG-4000 | |
|
ISG-8000 | |
|
...
2.1 Indoor Access Points:
ModelBlink-Verhalten aus der Hardware-Schnellübersicht - auf die Bilder klicken zum Vergrößern | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
L-321agn | | WLAN LED blinking red: Hardware error in the Wi-Fi module Auf der Oberseite des Gerätes befinden sich zwei weitere LEDsThere are two additional LEDs on the top side of the device:
- Linke Left LED: Power
- Rechte Right LED: WLAN Link
LED -Blink-Verhalten der Power-LED auf der Oberseiteblinking characteristics of the Power LED on the top side:
- orange / grün blinkend im Wechsel mit der green blinking alternately with the WLAN Link LED: Der Access Point sucht nach einem WLAN-Controller (Standard-Einstellung des WLAN-Moduls The access point is searching for a WLAN Controller (default setting of the Wi-Fi module "Managed")
- orange / rot blinkend im Wechsel mit der red blinking alternately with the WLAN Link LED: Der Access Point wird von einem WLAN-Controller verwaltet, der Profil-Bezug schlägt allerdings fehl, da Firmware und/oder Loader-Version des Access Points nicht mit dem WLAN-Controller kompatibel sind
- 1 x invers grün blinkend: Die LMC ist erreichbar, es besteht aber ein Problem in der LMC (theoretisches Problem, das niemals auftreten sollte)
- 2 x invers grün blinkend: Pairing-Fehler bzw. LMC-Aktivierungscode nicht vorhanden
- 3 x invers grün blinkend: LMC nicht erreichbar bzw. Kommunikationsfehler
LED-Blink-Verhalten der WLAN-Link LED auf der Oberseite im Modus "Managed" und "Basisstation": - Dauerhaft grün leuchtend: WLAN-Modul 1 aktiv
- 1 x Langsam grün blinkend: Ein WLAN-Teilnehmer hat sich verbunden (Signalstärke gut)
- Mehrfach grün blinkend: Zählt im Standard die Anzahl der verbundenen WLAN-Teilnehmer
LED-Blink-Verhalten der WLAN-Link LED auf der Oberseite im Modus "Client": - The access point is managed by a WLAN Controller but the WLAN profile cannot be obtained because the Firmware and/or Loader version of the access points aren't compatible with the WLAN Controller
- 1 x green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error
LED blinking characteristics of the WLAN Link LED on the top side in mode "Managed" and "Access point": - Glowing green permanently: Wi-Fi module active
- 1 x blinking green: A Wi-Fi device has connected (good signal quality)
- Blinking green multiple times: Counts the number of connected Wi-Fi devices (default setting)
LED blinking characteristics of the WLAN-Link LED on the top side in the mode "Station": - Blinking green slowly : Good signal quality to base station
- Blinking green fast: Bad signal quality to base station
- Langsam grün blinkend: Signalstärke zur Basis-Station gut
- Schnell grün blinkend: Signalstärke zur Basis-Station schwach
|
L-322agn / L-822acn / L-1302acn | Image RemovedImage Added | WLAN LED blinking red: Hardware error in the Wi-Fi module
Auf der Oberseite des Gerätes befinden sich zwei weitere LEDsThere are two additional LEDs on the top side of the device: - Linke Left LED: Power
- Rechte Right LED: WLAN Link
LED -Blink-Verhalten der Power-LED auf der Oberseiteblinking characteristics of the Power LED on the top side:
- orange / grün blinkend im Wechsel mit der green blinking alternately with the WLAN Link LED: Der Access Point sucht nach einem WLAN-Controller (Standard-Einstellung des WLAN-Moduls The access point is searching for a WLAN Controller (default setting of the Wi-Fi module "Managed")
- orange / rot blinkend im Wechsel mit der red blinking alternately with the WLAN Link LED: Der Access Point wird von einem WLAN-Controller verwaltet, der Profil-Bezug schlägt allerdings fehl, da Firmware und/oder Loader-Version des Access Points nicht mit dem WLAN-Controller kompatibel sind
- 1 x invers grün blinkend: Die LMC ist erreichbar, es besteht aber ein Problem in der LMC (theoretisches Problem, das niemals auftreten sollte)
- 2 x invers grün blinkend: Pairing-Fehler bzw. LMC-Aktivierungscode nicht vorhanden
- 3 x invers grün blinkend: LMC nicht erreichbar bzw. Kommunikationsfehler
LED-Blink-Verhalten der WLAN-Link LED auf der Oberseite im Modus "Managed" und "Basisstation": - orange/grün blinkend: Der Access Point sucht nach einem WLAN-Controller (Standard-Einstellung des WLAN-Moduls "Managed")
- Dauerhaft grün leuchtend: WLAN-Modul 1 aktiv
- 1 x Langsam grün blinkend: Ein WLAN-Teilnehmer hat sich verbunden (Signalstärke gut)
- Mehrfach grün blinkend: Zählt im Standard die Anzahl der verbundenen WLAN-Teilnehmer
LED-Blink-Verhalten der WLAN-Link LED auf der Oberseite im Modus "Client": Langsam grün blinkend: Signalstärke zur Basis-Station gutSchnell grün blinkend: Signalstärke zur Basis-Station schwach - The access point is managed by a WLAN Controller but the WLAN profile cannot be obtained because the Firmware and/or Loader version of the access points aren't compatible with the WLAN Controller
- 1 x green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error
LED blinking characteristics of the WLAN Link LED on the top side in mode "Managed" and "Access point": - Glowing green permanently: Wi-Fi module active
- 1 x blinking green: A Wi-Fi device has connected (good signal quality)
- Blinking green multiple times: Counts the number of connected Wi-Fi devices (default setting)
LED blinking characteristics of the WLAN-Link LED on the top side in the mode "Station": - Blinking green slowly : Good signal quality to base station
- Blinking green fast: Bad signal quality to base station
|
L-1310acn | Image Modified | WLAN LED blinking red: Hardware error in the Wi-Fi module
LED -Blink-Verhalten der Power-blinking characteristics of the power LED: invers grün blinkend: Die LMC ist erreichbar, es besteht aber ein Problem in der LMC (theoretisches Problem, das niemals auftreten sollte)- green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error
2 x invers grün blinkend: Pairing-Fehler bzw. LMC-Aktivierungscode nicht vorhanden3 x invers grün blinkend: LMC nicht erreichbar bzw. Kommunikationsfehler |
LN-630acn / LN-830U | Image RemovedImage Added |
|
LN-860 / LN-862 | Image RemovedImage Added |
|
LN-1700B / LN-1702B / LN-1700UE | Image RemovedImage Added |
|
LW-500 / LW-600 | Image RemovedImage Added |
|
LX-6400 / LX-6402 | | Power and WLAN Link LED blinking yellow / green in alternation: The access point is searching for a WLAN Controller |
2.2 Industrie Access Points:
ModelBlink-Verhalten aus der Hardware-Schnellübersicht - auf die Bilder klicken zum Vergrößern | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
IAP-821 | Image Modified | WLAN LED blinking red: Hardware error in the Wi-Fi module
LED -Blink-Verhalten der Power-blinking characteristics of the power LED: - 1 x invers grün blinkend: Die LMC ist erreichbar, es besteht aber ein Problem in der LMC (theoretisches Problem, das niemals auftreten sollte)
- 2 x invers grün blinkend: Pairing-Fehler bzw. LMC-Aktivierungscode nicht vorhanden
- green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error3 x invers grün blinkend: LMC nicht erreichbar bzw. Kommunikationsfehler
|
IAP-822 | Image Modified | WLAN LED blinking red: Hardware error in the Wi-Fi module
LED -Blink-Verhalten der Power-blinking characteristics of the power LED: - 1 x invers grün blinkend: Die LMC ist erreichbar, es besteht aber ein Problem in der LMC (theoretisches Problem, das niemals auftreten sollte)
- 2 x invers grün blinkend: Pairing-Fehler bzw. LMC-Aktivierungscode nicht vorhanden
- green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error3 x invers grün blinkend: LMC nicht erreichbar bzw. Kommunikationsfehler
|
2.3 Outdoor Access Points:
3. WLAN-Controller:
ModelBlink-Verhalten aus der Hardware-Schnellübersicht - auf die Bilder klicken zum Vergrößern | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
WLC-4006+ | Image RemovedImage Added | LED -Blink-Verhalten der Power-blinking characteristics of the power LED: - 1 x invers grün blinkend: Die LMC ist erreichbar, es besteht aber ein Problem in der LMC (theoretisches Problem, das niemals auftreten sollte)
- 2 x invers grün blinkend: Pairing-Fehler bzw. LMC-Aktivierungscode nicht vorhanden
- green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error3 x invers grün blinkend: LMC nicht erreichbar bzw. Kommunikationsfehler
|
WLC-1000 | Image Modified |
|