Versionen im Vergleich

Schlüssel

  • Diese Zeile wurde hinzugefügt.
  • Diese Zeile wurde entfernt.
  • Formatierung wurde geändert.


Seiteneigenschaften




Description:
With the ongoing migration of ISDN connections to All-IP, the ISDN connections available at sites are being converted into additional DSL connections. In order to provide this new bandwidth to the whole of the network, the router needs to be connected to the new DSL line.
If the DSL connection of the gateway is already in use, a LANCOM VDSL router can be connected upstream as a pure DSL modem. The access and VoIP data continue to be stored in the main gateway. This allows additional DSL connections to be transparently integrated into the existing scenario.
As of LCOS Version 10.20, all LANCOM VDSL routers can be switched to DSL Bridge mode. This allows the use of the devices as a pure DSL modem.


Hinweis

The Bridge mode refers only to the internal xDSL modems. If the router (additionally) has a built-in LTE modem, the LTE modem can not be operated in bridge mode!




Requirements:



Procedure:
1
.
) Configuration steps on the router used as a modem (Modem router):
1.1) Connect the LANCOM router, which is to operate as a modem, to the VDSL port.
1.2
Connect the main gateway to the LANCOM modem by means of an Ethernet cable.
) Open the configuration of the Modem router in LANconfig and go to the menu Interfaces → LAN → Ethernet ports.
Image Added
1.3
In the menu Interfaces → LAN → Port table, combine the LAN used and the xDSL interface in a free bridge group.
In this example, the logical interface LAN-1 and the interface XDSL-1 are combined in the unused bridge group BRG-2.
Also make sure that used
) Edit the Ethernet port to be used for administration of the router (in this example ETH 1) and make sure that the logical interface LAN-1 is
also assigned to the correct physical port (for example, ETH-1
assigned to it.
Image Added
1.4) Edit an unused Ethernet port to be used for the connection to the gateway router (in this example ETH 4) and select the interface LAN-2 as Interface usage
Image Added
1.5) Go to
). You can do this in
the menu Interfaces → LAN →
Interface Settings
LAN bridge.
Image Removed
1.5 Deactivate the DHCP server of the device in the menu IPv4 → DHCPv4 → DHCP networks.
Image Removed
1.6 In the
Image Added
1.
4 Switch to the menu Interface → WAN → Interface Settings → xDSL modem operation and configure the VDSL port to Bridge Mode.
  • For operation on VDSL connections no further parameter needs to be changed.
  • For ADSL connections (for example, Deutsche Telekom), you must configure the ATM parameters to the following values:
    • VPI: 1
    • VCI: 32
    • ATM-Modus: LLC-Mux
Image Removed
6) Make sure, that the option Connect by using a bridge (default) is selected and switch to the menu Port table afterwards.
Image Added
1.7) Make sure, that no Bridge group is assigned to the logical interface LAN-1.
Image Added
1.8) Edit the LAN interface selected in step 1.4 (in this example LAN-2) and the xDSL interface (in this example xDSL-1).
Assign an unused Bridge group to both interfaces (in this example BRG-2).
Image Added Image Added
1.9) The Port table has to appear as shown below afterwards.
Image Added
1.10) Go to the menu Interfaces → WAN → Interface settings → XDSL modem operation.
Image Added
1.11) In the dropdownmenu for the parameter Mode select the option Bridge.

Image Added

Info

Depending on your Internet provider it is possible that the parameters VPI, VCI and the ATM mode have to be changed. Please ask your provider if necessary.


1.12 In the menu

IPv4 → General → IP networks

menu,

assign

a local

an IP address from an unused IP

address

range

(for example,

to the network INTRANET (in this example 192.168.3.254/24 ) and make sure that the interface LAN-1 is selected (see step 1.3).


Hinweis

The assignment of an unused IP address range is mandatory. If an IP address from a local network configured on the Gateway router is entered on the Modem router and an IPoE remote site with an IP address from the local network is created on the Gateway router to ensure Management access (see step 3), the local network and the WAN (MANAGEMENT) will have the same IP address range. This will lead to routing problems! 

Image Added
Image Removed
Image Added
1.
7 make sure that
13) Deactivate the DHCP server of the device in the menu
Interfaces
IPv4
LAN → LAN bridge settings the option Connect using a bridge is activated.
DHCPv4 → DHCP networks.
Image Added
1.14) The configuration of the Modem router is now complete.
Image Removed
1.8
Write the configuration back to the device.


2
.
) Set up the Internet connection on the main gateway (Gateway router) :
In this example, the main gateway is a LANCOM 1781EF +. Since this device does not have a built-in VDSL modem, dial-up to the Internet should be carried out via the LANCOM 730VA, which was configured as VDSL modem in step 1.
2.1) Start the setup wizard in LANconfig and select the option Set up Internet access.
Image Removed
Image Added
2.2) In this example, a new IPv4 connection is to be created.
Image Removed
Image Added
2.3) Select the Ethernet interface (External Modem / Router) setting to use an external modem.
Image Removed
Image Added
2.4) In this example, the external VDSL modem is connected to the WAN port of the LANCOM router, so WAN must be selected as the Ethernet connector in the following dialog.
Image Removed
Image Added
2.5) Select your country.
Image Removed
Image Added
2.6) Select your Internet service provider in the following dialog.
Image Removed
Image Added
2.7) In the next dialog you have to select your product.
Image Removed
Image Added
2.8) In the following dialog, enter the access data that you received from your provider.
Image Removed
Image Added
2.9) Enter the VLAN tag that your provider uses. For Deutsche Telekom VDSL connections the VLAN-ID is 7.
Image Removed
Image Added
2.10) In this example, no backup connection is used.
Image Removed
Image Added
2.11) Quit the setup wizard to set up the Internet connection with the Finish button.
The configured values are then written to the LANCOM router.
Image Removed
Image Added
2.12) After the configuration has been written back to the device, the setup wizard asks if you want to continue with another wizard.
Click No in this dialog because the configuration steps to set up the VDSL connection are complete.
2.13) Connect the Gateway router to the Modem router by means of an Ethernet cable.


3
.
) Make sync status of the
LANCOM modem
Image Removed
3.2 Then switch to the menu Communication → Protocols → IP Parameters and create an entry with the following values:
  • Remote site: Management
IP address: an IP address from the IP address range configured in step 1.6 (e.g.
Modem router accessible from the network (optional) :
3.1
If the sync status of the LANCOM modem shall be accessible from the network, you must add a new remote site called MANAGEMENT in the menü Communication → Remote sites → Remote sites (DSL) with a hold short of 9999 seconds, the layer name IPOE and the DSL port 1.
) Configuring the Plain Ethernet connection via the setup wizard:
  • Select an unused Ethernet Port which deviates from the port selected in step 2.4 (in this example ETH 4).

 Image Added

  • In this step you have to assign an IP address as well as the corresponding Subnet Mask from the IP address range assigned in step 1.12 (in this example the IP address
  • 192.168.3.1
)Netmask: The netmask of the unused IP address range configured in step 1.6 (here
  • with the Subnet Mask 255.255.255.0).
Image Removed
3.3 In the create an entry for the network
Info

Entering a Default gateway is not necessary in this case, as no routing is to be performed via this connection.

Image Added

  • In this step it is imperative that you select the option Leave the current default route (not recommended). Otherwise the Internet connection set up in step 2 won't be functional anymore!

Image Added


3.2) Manual configuration steps on the Gateway router:
3.2.1) Open the configuration of the Gateway router in LANconfig and go to the menu IP Router → Routing → IPv4 routing table
menu,
.
Image Added
3.2.2) Click Add to create a new routing entry.
Image Added
3.2.3) Edit the following parameters:
  • IP address: Enter the network address of the network entered in step 1.12 and 3.1 (in this example
Image Removed
3.4
  • 192.168.3.0
/24, which points to the remote site Management and in which IP masking is deactivated.
  • ).
  • Netmask: Enter the corresponding Subnet Mask (in this example 255.255.255.0)
  • Router: In the dropdownmenu select the Internet remote site created via the setup wizard in step 3.1 (in this example MANAGEMEN). 
  • IP masquerading: Select the option IP Masquerading switched off.

Image Added

3.2.4)
Write the configuration back to the device.
The
LANCOM modem
Modem router can now be reached and read out via the IP address 192.168.3.254.


Info

The sync status of the

xDSL

Modem router is also indicated by the xDSL-LED. When using the Bridge-Mode only the sync status is displayed. During active DSL sync the LED shines green permanently.