Description:
This article describes the meaning of LED blinking characteristics of LANCOM routers and access points.
Info |
---|
If all LEDs glow red permanently, there are two possible causes: - The LEDs were set to red via the LED test (Setup/Config/LED-Test). The LEDs can be set to red, green and orange and can also be deactivated via the LED test. In this case the device works normally.
- The reset button is jammed. In this case the device is in a reset loop and doesn't function normally.
|
1) LANCOM router:
Info |
---|
Routers in CPE case (all routers except IAP-4G+, IAP-1781VAW, 190x Serie and Central Site Gateways) feature two additional LEDs on the top side: - Left LED: Power
- Right LED: Online
|
1.1) VPN router:
Model | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
1640E | |
|
1780EW-4G+ | | WLAN LED blinking red: Hardware error in the Wi-Fi module |
1781EW+ | | WLAN LED blinking red: Hardware error in the Wi-Fi module
LED blinking characteristics of the power LED: - 1 x green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error
|
1781VA | |
|
1790-4G | |
|
1790EF | |
|
1790VA | |
|
1790VA-4G | |
|
1790VAW | | WLAN LED blinking red: Hardware error in the Wi-Fi module |
1900EF | |
|
1906VA | |
|
1906VA-4G | |
|
IAP-4G+ | |
|
1.2 VoIP-Router:
Model | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
883 VoIP / 883+ VoIP / 1793VAW | | WLAN LED blinking red: Hardware error in the Wi-Fi module |
884 VoIP / 1784VA | |
|
1793VA | |
|
1793VA-4G | |
|
| | WLAN LED blinking red: Hardware error in the Wi-Fi module |
1.3 Central Site Gateways:
Model | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
ISG-1000 | |
|
ISG-4000 | |
|
ISG-8000 | |
|
2. LANCOM Access Points:
2.1 Indoor Access Points:
Model | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
L-321agn | | WLAN LED blinking red: Hardware error in the Wi-Fi module Auf der Oberseite des Gerätes befinden sich zwei weitere LEDs:
- Linke LED: Power
- Rechte LED: WLAN Link
LED-Blink-Verhalten der Power-LED auf der Oberseite:
- orange / grün blinkend im Wechsel mit der WLAN Link LED: Der Access Point sucht nach einem WLAN-Controller (Standard-Einstellung des WLAN-Moduls "Managed")
- orange / rot blinkend im Wechsel mit der WLAN Link LED: Der Access Point wird von einem WLAN-Controller verwaltet, der Profil-Bezug schlägt allerdings fehl, da Firmware und/oder Loader-Version des Access Points nicht mit dem WLAN-Controller kompatibel sind
- 1 x invers grün blinkend: Die LMC ist erreichbar, es besteht aber ein Problem in der LMC (theoretisches Problem, das niemals auftreten sollte)
- 2 x invers grün blinkend: Pairing-Fehler bzw. LMC-Aktivierungscode nicht vorhanden
- 3 x invers grün blinkend: LMC nicht erreichbar bzw. Kommunikationsfehler
LED-Blink-Verhalten der WLAN-Link LED auf der Oberseite im Modus "Managed" und "Basisstation": - Dauerhaft grün leuchtend: WLAN-Modul 1 aktiv
- 1 x Langsam grün blinkend: Ein WLAN-Teilnehmer hat sich verbunden (Signalstärke gut)
- Mehrfach grün blinkend: Zählt im Standard die Anzahl der verbundenen WLAN-Teilnehmer
LED-Blink-Verhalten der WLAN-Link LED auf der Oberseite im Modus "Client": - Langsam grün blinkend: Signalstärke zur Basis-Station gut
- Schnell grün blinkend: Signalstärke zur Basis-Station schwach
|
L-322agn / L-822acn / L-1302acn | | WLAN LED blinking red: Hardware error in the Wi-Fi module Auf der Oberseite des Gerätes befinden sich zwei weitere LEDs:
- Linke LED: Power
- Rechte LED: WLAN Link
LED-Blink-Verhalten der Power-LED auf der Oberseite:
- orange / grün blinkend im Wechsel mit der WLAN Link LED: Der Access Point sucht nach einem WLAN-Controller (Standard-Einstellung des WLAN-Moduls "Managed")
- orange / rot blinkend im Wechsel mit der WLAN Link LED: Der Access Point wird von einem WLAN-Controller verwaltet, der Profil-Bezug schlägt allerdings fehl, da Firmware und/oder Loader-Version des Access Points nicht mit dem WLAN-Controller kompatibel sind
- 1 x invers grün blinkend: Die LMC ist erreichbar, es besteht aber ein Problem in der LMC (theoretisches Problem, das niemals auftreten sollte)
- 2 x invers grün blinkend: Pairing-Fehler bzw. LMC-Aktivierungscode nicht vorhanden
- 3 x invers grün blinkend: LMC nicht erreichbar bzw. Kommunikationsfehler
LED-Blink-Verhalten der WLAN-Link LED auf der Oberseite im Modus "Managed" und "Basisstation": - orange/grün blinkend: Der Access Point sucht nach einem WLAN-Controller (Standard-Einstellung des WLAN-Moduls "Managed")
- Dauerhaft grün leuchtend: WLAN-Modul 1 aktiv
- 1 x Langsam grün blinkend: Ein WLAN-Teilnehmer hat sich verbunden (Signalstärke gut)
- Mehrfach grün blinkend: Zählt im Standard die Anzahl der verbundenen WLAN-Teilnehmer
LED-Blink-Verhalten der WLAN-Link LED auf der Oberseite im Modus "Client": - Langsam grün blinkend: Signalstärke zur Basis-Station gut
- Schnell grün blinkend: Signalstärke zur Basis-Station schwach
|
L-1310acn | | WLAN LED blinking red: Hardware error in the Wi-Fi module
LED blinking characteristics of the power LED: - 1 x green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error
|
LN-630acn / LN-830U | |
|
LN-860 / LN-862 | |
|
LN-1700B / LN-1702B / LN-1700UE | |
|
LW-500 / LW-600 | |
|
LX-6400 / LX-6402 | |
|
2.2 Industrie Access Points:
Model | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
IAP-821 | | WLAN LED blinking red: Hardware error in the Wi-Fi module
LED blinking characteristics of the power LED: - 1 x green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error
|
IAP-822 | | WLAN LED blinking red: Hardware error in the Wi-Fi module
LED blinking characteristics of the power LED: - 1 x green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error
|
2.3 Outdoor Access Points:
Model | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
OAP-821 | | WLAN LED blinking red: Hardware error in the Wi-Fi module |
OAP-822 / OAP-830 | | WLAN LED blinking red: Hardware error in the Wi-Fi module |
OAP-1700B / OAP-1702B | | WLAN LED blinking red: Hardware error in the Wi-Fi module |
3. WLAN-Controller:
Model | Blinking characteristics in the Quick Reference Guide - click to enlarge | Annotations |
---|
WLC-4006+ | | LED blinking characteristics of the power LED: - 1 x green inverse blinking: The LMC is reachable but there is an issue within the LMC (theoretical problem which should never arise)
- 2 x green inverse blinking: Pairing error or activation code doesn't exist
- 3 x green inverse blinking: LMC not reachable or communication error
|
WLC-1000 | |
|